Splicing Tape
for connecting carrier tape
Splicing tape is desined for modular type mounters.
Enable to increase in efficiency and save time from your mounting process by splicing the next carrier tape before the components are finished to be mounted with joint tape.
Other tape products
We offer our tape products that take advantage of the double-faced adhesive tape for use in rationalization of the operation in SMT and ASSY of PCB.
Insulating moistureproof coating 
Comformal coating series
The mounting density of PCBs can be called the heart of electronic appliances and equipment. This mounting density has increasingly become higher to result in the narrowing of space between leads. Furthermore, usage requires PCBs products to stand against a variety of application environments. Some problem causing factors at issue lately are moisture, condensation, oil, detergent, impurities, cohesion of mold, dead insects dust and lead breaks due to vibration have not been addressed adequately at this time. "Seal-glo insulating moistureproof coatings” dries into a thin film at room temperature, while maintaining excellent anti-moisture and insulating properties. This coating will stabilize components as it seals out moisture ( known as conformal coating applied for several types of circuit boards) and numerous types of electronic parts. We are confident that “Seal-glo insulating moisture-proof coatings” will surely enhance the quality and reliability of the electronic equipment that it is applied to.
UV conformal coating UV Series
Seal-glo 602MCF is the insulating moisture-proof coating designed to cure with UV.
Contribute your productivity improvement by curing with UV. Provide high curing performance at unirradiated area due to its moisture cure property.
Adheshive for chip devices NESeries
“Seal-glo NE series” are a range of adhesives developed for temporary chip-bonding, prior to the wave-soldering process. They are all single component, heat-curing, epoxy adhesives which have excellent preservation qualities.“Seal-glo NE series” not only have rapid curing properties, with a 1～2 minute heating duration between 90～150℃, as required for SMD mounting, but their fine properties enable them to be applied by both high speed dispensing and screen printing alike. We have a wide range and variety of grades to meet specific customer requirements.
Underfill for BGA / CSP UF Series
In response to consumer demand for even slimmer, more light-weight mobile appliances, the corresponding level of integration needed to meet this requirement led to the development of BGA (Ball Grid Array) and CSP (Chip Size Package) technology, thus replacing previously used QFP (Quad Flat Pack) components. Now in widespread use throughout the electronics industry, BGA and CSP components are connected to the circuit board by means of minute solder balls. However, stresses such as heat cycling, board warping and thermal shock, can sometimes interrupt the connection between the BGA and/or the CSP and the circuit board. To prevent this, Fuji Chemical have developed Seal-glo UF300 Series, an underfill agent which readily penetrates the gaps between the BGA and/or CSP and the circuit board, in turn, contributing to improved bonding reliability. As Seal-glo UF300 Series hardens, it reduces stress and also reinforces the solder bonding. Easily repairable, Seal-glo UF300 Series permits the re-use of expensive electronic parts and circuit boards, thus offering substantial savings.
LTG series
Seal-glo LTG series is one-component thermosetting epoxy adhesive developed for fixation of LED backlight lens.
RED Cleaner
Seal-glo RED Cleaner is a water based cleaner for Seal-glo chip adhesive
Magazine stick
Magazine stick is extrusion molded engineering plastic used for mounting, wrapping and packaging of electronic parts such as connectors, semi-conductors, resin molded, metal parts and pressed parts. In addition, the product is pretty durable due to its martial characteristics, and it can be re-used in more times than non-polycarbonate sticks to result in reduction of auxiliary material and waste disposal costs.
2016.10.21
Contribute your productivity improvement by curing with UV.
Can provide high hardenability at unirradiated area due to its moisture cure property.
Solventless, VOC free.
Excels in moisture and sulfide gas resistances.
Various reliability studies have shown that agent retains stable property.
usable to Thick coating and Potting.
| Item | Seal-glo 602MCF |
|---|---|
| Main resin | Urethane acrylate |
| Viscosity | 100mPa･s |
| Curing condition | 1000-3000mJ/cm2 |
| Moisture cure property | about 3 days |
| package style | 1Kg、5Kg、20Kg(can) |
201610.21
For our company that continues to be involved with various print board peripheral themes of various equipment such as home appliances, air conditioning/communication equipment, automation equipment and control equipment of factories, as well as societal infrastructure equipment (transportation) such as cars and trains, the evaluation techniques needed for the confirmation of reliability is an important asset.
Viscometer
Super insulation
resistance meter
Microscope
FT-IR
Pulling testing equipment
Thermostat chamber
Thermal shock chamber
Ion migration evaluation system
Salt Spray Test Instrument
Screen Printer
Conformal Coating Systems
UV curing equipment
Compact type reflow
Handy type
Standalone conveyor
LED batch irradiator
| Item | Viscosity （25℃） | Thixotropy index | Curing condition | Applying method | Storage condition |
|---|---|---|---|---|---|
 Seal-glo NE7250H |
300Pa･s | 5.0 | 120℃/60sec 110℃/90sec |
Screen printing Thick mask |
Refrigerated storage at 2～10 ℃ |
| Seal-glo NE7200H | 300Pa･s | 7.0 | 140℃/60sec 120℃/90sec |
High-speed dispenser Screen printing Thick mask |
|
| Seal-glo NE7300H | 320Pa･s | 7.1 | 100℃/60sec 90℃/90sec |
||
| Seal-glo NE8800K | 300Pa･s | 6.8 | 150℃/60sec 140℃/90sec |
High-speed dispenser | |
| Seal-glo NE8800T | 310Pa･s | 6.3 | 150℃/60sec 130℃/90sec |
||
| Seal-glo NE3000S | 390Pa･s | 5.0 | 150℃/60sec 130℃/90sec |
Screen printing Thick mask |
|
| Seal-glo NE3300H | 310Pa･s | 6.1 | 140℃/60se 130℃/90sec |
*NE3000S,NE3300H,NE7200H,NE7300H,NE7250H: Halogen-Free
201610.21
| Package style | Contens | Unit | Applicable Dispenser Makers |
|---|---|---|---|
| Cartridge | 200gr | - | For Our filling machines only |
| A Syringe | 30cc | - | Panasert(HDF)、HITACHI、TDK、TOSHIBA、 SONY、 CASIO、YAMAHA、JUKI |
| B Syringe | 30cc | - | FUJI |
| D Syringe | 20cc | - | Panasert（Short: MK, MV） |
| E Syringe | 10cc | - | TENRYU, TOSHIBA, YAMAHA, JUKI, CASIO |
For our company that continues to be involved with various print board peripheral themes of various equipment such as home appliances, air conditioning/communication equipment, automation equipment and control equipment of factories, as well as societal infrastructure equipment (transportation) such as cars and trains, the evaluation techniques needed for the confirmation of reliability is an important asset.
Viscometer
Super insulation
resistance meterMicroscope
FT-IR
Pulling testing equipment
Thermostat chamber
Thermal shock chamber
Ion migration evaluation system
Salt Spray Test Instrument
Screen Printer
Conformal Coating Systems
UV curing equipment
Compact type reflow
| Item | Appearance | Viscosity | Gelation time | Tg | Shelf life | Curing condition | Package |
|---|---|---|---|---|---|---|---|
| Seal-glo UF200H |
Black | 3000mPa･s | 23 sec. | 95℃ | 8 month（10℃） | 120℃×10 min. | - |
| Seal-glo UF317H | Black | 1600mPa･s | 16 sec | 53℃ | 8 month（10℃） | 120℃×10 min | 140g |
| Seal-glo UF330H | Black | 3300mPa･s | 16 sec | 72℃ | 8 month（10℃） | 120℃×10 min | 160g |
| Seal-glo F346HW | White | 1400mPa･s | 18 sec | 19℃ | 8 month(10℃） | 120℃×5 min | 180g |
201610.21
For our company that continues to be involved with various print board peripheral themes of various equipment such as home appliances, air conditioning/communication equipment, automation equipment and control equipment of factories, as well as societal infrastructure equipment (transportation) such as cars and trains, the evaluation techniques needed for the confirmation of reliability is an important asset.
Viscometer
Super insulation
resistance meterMicroscope
FT-IR
Pulling testing equipment
Thermostat chamber
Thermal shock chamber
Ion migration evaluation system
Salt Spray Test Instrument
Screen Printer
Conformal Coating Systems
UV curing equipment
Compact type reflow
■Features
Retains enough adhesive strength at 80 ℃ for 3 minutes.
Stable shape without slumping and stringing with not only dispensing but also screen printing.
Brightness level increases because white color adhesive.（LTG800W）
Improved heat-shock resistance in comparison to conventional products（LTG800W）
■Characteristic
| Item | Unit | LTG800 | LTG800W |
|---|---|---|---|
| Appearance | ― | Black liquid | White liquid |
| Viscosity（23℃） | Pa･s | 100 | 80 |
| Thixotripy（23℃） | ― | 6.0 | 7.0 |
| Specific gravity（23℃） | ― | 1.48 | 1.49 |
| Cure condition | ― | 60℃×30 min. 80℃×3 min. |
60℃×30 min. 80℃×3 min. |
Store the products in a refrigerator at -20 degrees C with the lid of container tightly closed.
Seal-glo RED Cleaner is a cleaner for Seal-glo chip adhesive. This is suited to clean the dispenser nozzle and the screen mask. This cleaner's performance is much higher in spite of water-base. Seal-glo RED Cleaner does not contain VOC compounds and cancer-causing substances in order to reduce worker’s burden, Earth-friendly cleaner, which does not contain air pollutants and ozone-depleting substances either.
■Specifications
| Item | Characterristics |
|---|---|
| Water dilutability (％) | 30～35 |
| Appearance | Transeparent liquid |
| Density(g/mL ，～22℃) | 1.06 |
| pH | 5.6 |
| Odor | Mild |
| % VOC Content | 0% |
| Shelf life | 1 year |
| Package | 1KG Plastic bottle 20KG Plastic tankク |
2016.10.21
For our company that continues to be involved with various print board peripheral themes of various equipment such as home appliances, air conditioning/communication equipment, automation equipment and control equipment of factories, as well as societal infrastructure equipment (transportation) such as cars and trains, the evaluation techniques needed for the confirmation of reliability is an important asset.
Viscometer
Super insulation
resistance meterMicroscope
FT-IR
Pulling testing equipment
Thermostat chamber
Thermal shock chamber
Ion migration evaluation system
Salt Spray Test Instrument
Screen Printer
Conformal Coating Systems
UV curing equipment
Compact type reflow
■Features
Retains enough adhesive strength at 80 ℃ for 3 minutes.
Stable shape without slumping and stringing with not only dispensing but also screen printing.
Brightness level increases because white color adhesive.（LTG800W）
Improved heat-shock resistance in comparison to conventional products（LTG800W）
■Characteristic
| Item | Unit | LTG800 | LTG800W |
|---|---|---|---|
| Appearance | ― | Black liquid | White liquid |
| Viscosity（23℃） | Pa･s | 100 | 80 |
| Thixotripy（23℃） | ― | 6.0 | 7.0 |
| Specific gravity（23℃） | ― | 1.48 | 1.49 |
| Cure condition | ― | 60℃×30 min. 80℃×3 min. |
60℃×30 min. 80℃×3 min. |
Store the products in a refrigerator at -20 degrees C with the lid of container tightly closed.
Seal-glo RED Cleaner is a cleaner for Seal-glo chip adhesive. This is suited to clean the dispenser nozzle and the screen mask. This cleaner's performance is much higher in spite of water-base. Seal-glo RED Cleaner does not contain VOC compounds and cancer-causing substances in order to reduce worker’s burden, Earth-friendly cleaner, which does not contain air pollutants and ozone-depleting substances either.
■Specifications
| Item | Characterristics |
|---|---|
| Water dilutability (％) | 30～35 |
| Appearance | Transeparent liquid |
| Density(g/mL ，～22℃) | 1.06 |
| pH | 5.6 |
| Odor | Mild |
| % VOC Content | 0% |
| Shelf life | 1 year |
| Package | 1KG Plastic bottle 20KG Plastic tankク |
2016.10.21
For our company that continues to be involved with various print board peripheral themes of various equipment such as home appliances, air conditioning/communication equipment, automation equipment and control equipment of factories, as well as societal infrastructure equipment (transportation) such as cars and trains, the evaluation techniques needed for the confirmation of reliability is an important asset.
Viscometer
Super insulation
resistance meterMicroscope
FT-IR
Pulling testing equipment
Thermostat chamber
Thermal shock chamber
Ion migration evaluation system
Salt Spray Test Instrument
Screen Printer
Conformal Coating Systems
UV curing equipment
Compact type reflow
Conformal coating for PCBs of home appliances, industrial electronic devices and automobile in order to moisture proof, dust prevention, and antifouling.
Airtight seal for moisture proof and insulating to the coil , trance, relay and hybrid IC.
Oil resistance, Salt water resistance, Resistance to corrosion by hydrogen sulfid gas
Coating administrations by UV
It's easy to find uneven or missing coating due to containing fluorescent agent. (except for 435K)
- Product use Features
- ･ Home appliances, Business machines, Industrial machines, Housing and Facilities
| Item | Main resin | Viscosity（25℃） | Solvent | Package | Characteristics |
|---|---|---|---|---|---|
| Seal-glo 630RF |
Rubber | 120mPa･s | Thinner G Thinner GL |
3Kg can 15KgUN can 420cc spray |
Registered product as UL94V-0 |
| Seal-glo 630RB |
120mPa･s | 3Kg can 15KgUN can |
Blue colored | ||
| Seal-glo 630RB-H |
400mPa･s | 3Kg can 15KgUN can |
630RB is suitable for thick film applcation due to high viscosity | ||
| Seal-glo 620UAF |
Urethane | 50mPa･s | Thinner H | 3Kg can 15KgUN can |
Aromatic compound-Fee Registered product as UL94V-0 |
| Seal-glo 435K |
Polyester | 170mPa･s | Thinner E Thinner P |
3Kg can 15KgUN can 300cc spray |
High gas barrier characteristics |
| Seal-glo 435KF |
Polyester | 170mPa･s | Thinner E Thinner P |
3Kg can 15KgUN can |
Registered product as UL94V-0 |
201610.21
For our company that continues to be involved with various print board peripheral themes of various equipment such as home appliances, air conditioning/communication equipment, automation equipment and control equipment of factories, as well as societal infrastructure equipment (transportation) such as cars and trains, the evaluation techniques needed for the confirmation of reliability is an important asset.
Viscometer
Super insulation
resistance meterMicroscope
FT-IR
Pulling testing equipment
Thermostat chamber
Thermal shock chamber
Ion migration evaluation system
Salt Spray Test Instrument
Screen Printer
Conformal Coating Systems
UV curing equipment
Compact type reflow
Dipping coat
Conformal Coating Systems
Magazine stick
Examples：Automatic mounting, carrying between locations, carrying precision, transferring overseas, baking, reuse , visual inspection
Industries supplied to：Automotive device manufacturers, Electric device and semiconductor manufacture, Electrical equipment manufacture
- Super high precision measurement
- Available in small quantities Flexible for designs
- Own designed
- High durability
- Heat resistance
- Environmentally
Conductive coating stick （SP Coating）
New type of magazine sticks which redeem defects of conventional antistatic-agent magazine sticks (surfactant-based) and magazine sticks made of carbon-contained resin.
- Conductivity
- High durability
- Heat resistance
- Environmentally
- Precision measurement
It is a standard-type (for general purposes) magazine stick for which we have received many requests.
There is no cost to the user for the price of a mold
As an option (additional cost), static electricity-proofing and printing of the company name/product number is possible.
We accept orders for small lots from 500 pieces
Semiconductor Dip Magazine Stick (for General Purposes)
It is compatible with most manufacturers that handle Dip parts.
Magazine Stick (for General Purposes) for Semiconductor/Transistor TO-220
It is compatible with most manufacturers that handle TO-220 parts, and it can be used for lead-formed parts.
* Items other than the two products mentioned above can be custom produced (mold production).
- Versatility
- High durability
- Heat resistance
- Environmentally
■Other Products
| Odd-shaped extrusion molding products | Odd-shaped extrusion molding products |
|---|---|
| Odd-shaped extrusion tube | Odd-shaped extrusion tube (transfer tube for chips) |
| Plastic Pipe and Plastic round bar | Coil bobbin, spacer, various materials for cutting work |
| Spring | Plastic spring （accessary, nonmagnetism, clutch） |
| Extrusion molding rubber | Rubber stopper for Magazine-stick |
| Vacuum forming tray | Vacuum forming tray for automatic mounting machine |
For our company that continues to be involved with various print board peripheral themes of various equipment such as home appliances, air conditioning/communication equipment, automation equipment and control equipment of factories, as well as societal infrastructure equipment (transportation) such as cars and trains, the evaluation techniques needed for the confirmation of reliability is an important asset.
Viscometer
Super insulation
resistance meterMicroscope
FT-IR
Pulling testing equipment
Thermostat chamber
Thermal shock chamber
Ion migration evaluation system
Salt Spray Test Instrument
Screen Printer
Conformal Coating Systems
UV curing equipment
Compact type reflow
With the “Joint Tape FC/LC Series” splicing tape of the carrier tape for electronic parts, strong connections are simple without using reinforcing metal plates. The peeling of the connection part or clogging of the carrier tape at the opening of the tape feeder does not occur. It improves the operation rate of the mounter.
Because it is structured in three pieces, there is less floating of the top tape and bending of the connection part caused by twisting of the connection part found in the two-piece-structure standard tapes available on the market, and therefore clogging of the tape at the opening of the tape feeder does not occur.
The Black tape products correspond well to joint detection functions, and there is a static electricity prevention function.
The strong adhesive strength holds connecting parts together, making a reinforcing metal plate unnecessary.
Since it comes with a locating jig function for connecting, precise connections are possible.
Enable to increase in efficiency and save time from your mounting process by splicing the next carrier tape before the components are finished to be mounted with joint tape.
Specfications
| FC8A | FC8B | LC8H |
|---|---|---|
 |
 |
 |
| For 8mm wide paper carrier tapes | For 8mm wide paper, Emboss carrier tapes | For 8mm wide paper, Emboss carrier tapes |
| S-type | M-type | L-type |
 |
 |
 |
| For 8mm wide paper, Emboss carrier tapes | For 12mm・16mm wide Emboss carrier tapes | For 24mm wide Emboss carrier tapes, 24mm and wider |
Function of detecting splicing point and ESD type
| FC8TS | FC8QE | FC24QE |
|---|---|---|
 |
 |
 |
| For 8mm wide pape carrier tapes | For 8mm wide paper, Emboss carrier tapes | |
| FC12QE | FC16QE | |
 |
 |
|
| For 12mm wide Emboss carrier tapes | For 16mm wide Emboss carrier tapes | |
| LC8BT | LC12BT | LC01BT |
 |
 |
 |
| For 8mm wide paper, Emboss carrier tapes | For 12mm wide Emboss carrier tapes | Supporting tape for 12mm wide emboss carrier tapes and wider. |
| Characteristics | FC series | LC series |
|---|---|---|
| Adhesion | Strong | Strong |
| Holding force(*) | Strong | Week |
| － | Positioning Guide | |
| Price | - | - |
Cutting tool for 8mm wide paper carrier tapes
By placing the tapes holes on to the positioning pins, anyone can simply perform the same cutting consistenly and accurately.
Positioning adjustment to each chip size is not necessary when using the cutting tool
Splicing tape procedureWhen detaching carrier tapes with remaining electrical components, there is a chance that those components may drop out if the top tape on its end peels off prematurely. SMT sealing tape is used to prevent component. Carrier tapes can be set in the feeder with this tape on, so it resolves the complicated process of reattaching with cellophane tape as done previously.
SMT Sealing Tape fits all carrier tapes regardless of tape width (one size fits all). You DO NOT need to use different tapes for each width carrier tapes.
Use for tape
This tape demonstrates the mounting of chip components.
This tape adheres the PCBs to the test mounting, then it confirms whether components are adhered properly by mechanical inspection machine.
This tape is reusable when the supply of PCBs and parts is not sufficient.
Characteristics
You can reuse the PCBs and components after the demonstration because you can peel the tapes off without the adhesive compound sticking to them.
The strength of the peel is stronger than the standard double-stick tape, as a result when peeled off the thin PCBs do not break.
This is extremely effective while mounting numerous chip devices on large-sized PCBs.
The alternative tape for prevention components drop out to the rubber stopper of Magazine-stick. The adhesive compound is difficult to transition. We designed not to contact the adhesive face to the contact face of the components.
For our company that continues to be involved with various print board peripheral themes of various equipment such as home appliances, air conditioning/communication equipment, automation equipment and control equipment of factories, as well as societal infrastructure equipment (transportation) such as cars and trains, the evaluation techniques needed for the confirmation of reliability is an important asset.
Viscometer
Super insulation
resistance meterMicroscope
FT-IR
Pulling testing equipment
Thermostat chamber
Thermal shock chamber
Ion migration evaluation system
Salt Spray Test Instrument
Screen Printer
Conformal Coating Systems
UV curing equipment
Compact type reflow
With the “Joint Tape FC/LC Series” splicing tape of the carrier tape for electronic parts, strong connections are simple without using reinforcing metal plates. The peeling of the connection part or clogging of the carrier tape at the opening of the tape feeder does not occur. It improves the operation rate of the mounter.
Because it is structured in three pieces, there is less floating of the top tape and bending of the connection part caused by twisting of the connection part found in the two-piece-structure standard tapes available on the market, and therefore clogging of the tape at the opening of the tape feeder does not occur.
The Black tape products correspond well to joint detection functions, and there is a static electricity prevention function.
The strong adhesive strength holds connecting parts together, making a reinforcing metal plate unnecessary.
Since it comes with a locating jig function for connecting, precise connections are possible.
Enable to increase in efficiency and save time from your mounting process by splicing the next carrier tape before the components are finished to be mounted with joint tape.
Specfications
| FC8A | FC8B | LC8H |
|---|---|---|
|
|
|
| For 8mm wide paper carrier tapes | For 8mm wide paper, Emboss carrier tapes | For 8mm wide paper, Emboss carrier tapes |
| S-type | M-type | L-type |
|
|
|
| For 8mm wide paper, Emboss carrier tapes | For 12mm・16mm wide Emboss carrier tapes | For 24mm wide Emboss carrier tapes, 24mm and wider |
Function of detecting splicing point and ESD type
| FC8TS | FC8QE | FC24QE |
|---|---|---|
|
|
|
| For 8mm wide pape carrier tapes | For 8mm wide paper, Emboss carrier tapes | |
| FC12QE | FC16QE | |
|
|
|
| For 12mm wide Emboss carrier tapes | For 16mm wide Emboss carrier tapes | |
| LC8BT | LC12BT | LC01BT |
|
|
|
| For 8mm wide paper, Emboss carrier tapes | For 12mm wide Emboss carrier tapes | Supporting tape for 12mm wide emboss carrier tapes and wider. |
| Characteristics | FC series | LC series |
|---|---|---|
| Adhesion | Strong | Strong |
| Holding force(*) | Strong | Week |
| － | Positioning Guide | |
| Price | - | - |
Cutting tool for 8mm wide paper carrier tapes
By placing the tapes holes on to the positioning pins, anyone can simply perform the same cutting consistenly and accurately.
Positioning adjustment to each chip size is not necessary when using the cutting tool
Splicing tape procedureWhen detaching carrier tapes with remaining electrical components, there is a chance that those components may drop out if the top tape on its end peels off prematurely. SMT sealing tape is used to prevent component. Carrier tapes can be set in the feeder with this tape on, so it resolves the complicated process of reattaching with cellophane tape as done previously.
SMT Sealing Tape fits all carrier tapes regardless of tape width (one size fits all). You DO NOT need to use different tapes for each width carrier tapes.
Use for tape
This tape demonstrates the mounting of chip components.
This tape adheres the PCBs to the test mounting, then it confirms whether components are adhered properly by mechanical inspection machine.
This tape is reusable when the supply of PCBs and parts is not sufficient.
Characteristics
You can reuse the PCBs and components after the demonstration because you can peel the tapes off without the adhesive compound sticking to them.
The strength of the peel is stronger than the standard double-stick tape, as a result when peeled off the thin PCBs do not break.
This is extremely effective while mounting numerous chip devices on large-sized PCBs.
The alternative tape for prevention components drop out to the rubber stopper of Magazine-stick. The adhesive compound is difficult to transition. We designed not to contact the adhesive face to the contact face of the components.
For our company that continues to be involved with various print board peripheral themes of various equipment such as home appliances, air conditioning/communication equipment, automation equipment and control equipment of factories, as well as societal infrastructure equipment (transportation) such as cars and trains, the evaluation techniques needed for the confirmation of reliability is an important asset.
Viscometer
Super insulation
resistance meterMicroscope
FT-IR
Pulling testing equipment
Thermostat chamber
Thermal shock chamber
Ion migration evaluation system
Salt Spray Test Instrument
Screen Printer
Conformal Coating Systems
UV curing equipment
Compact type reflow